Product added to your wishlist! View wishlist
Sign in to see your saved products on any device
Product removed from your wishlist! View wishlist
Sign in to see your saved products on any device
Something went wrong. Please try again later.
Product is added to compare already. Please refresh the page.
Product is not found in compare. Please refresh the page.
5 Products already added. Please delete existing selection to add this.
Share
Micron CSC Antifouling Paint, Shark White, Gallon by Interlux | For Boats | Boat Maintenance at West Marine
See more belowColor : Shark White
Sorry, We couldn't find this product
Description
Micron CSC Antifouling Paint, Shark White, Gallon by Interlux | For Boats | Boat Maintenance at West Marine. Micron CSC provides multi-season antifouling protection against all types of marine fouling organisms. When the time comes to apply new antifouling paint to your boats hull, the job will be a lot easier if you use Micron CSC. This is because compared to hard antifouling paints, Micron CSCs ablative formula wears away or "self-polishes" in a controlled fashion as the boat is used. Controlled polishing reduces the build-up of old coatings-which minimizes the need for laborious sanding at haulout. And compared to hard antifouling paints, Micron CSC is also better for the environment. This is because it uses less copper more efficiently than traditional, hard antifouling paints. Boats painted with Micron CSC can also be hauled, stored and relaunched without a loss of antifouling effectiveness-which means you can paint in the fall and splash in the spring! Interlux Ultimate No Sand System Key Features Fast-drying formula Antifouling performance for all fouling waters Suitable for powerboats and sailboats Multi-season protection Self-polishing formula reduces paint build-up Reduces need for sanding prior to repainting Physical Data Vehicle type: Copolymer ablative Finish: Matte Components: 1 Curing mechanism: Solvent release Solids by Volume: (Theoretical): 58% Coverage: 440sq.ft./gal. VOC: 370 grams/liter (as supplied) Active ingredients: 37.2% Cuprous oxide Application Application Method: Brush, roller, airless, or conventional spray Number of coats recommended: 2-3 Minimum per season with additional coats for extended service. Bare wood: 3 coats (first thinned) Wet Film Thickness: 3.4 mils/coat Dry Film Thickness: 2 mils/coat Applicator: High-quality short nap roller (maximum 3/16" nap) Application temperature: Min. /Max. Range: 10C/50F and maximum 35C/95F. Thinner: 216, Model 117598 or 433, Model 203679 Drying Times Drying @50F @73F @95F To touch 4 hr. 4 hr. 1 hr. To recoat 16 hr. 16 hr. 16 hr. To launch 16 hr. 16 hr. 16 hr. *The above dry times are minimums. May be recorded after the minimum time shown. There is no maximum dry time before launching. Get the right amount of paint: Boat Type Bottom Paint 10' Dinghy 1 qt. 14' Outboard 1-2 qt. 18' Runabout 2 qt. 20' Sailboat 3 qt. 24' Runabout 3-4 qt. 30' Sailboat 1.5 gal. 32' Cruiser 1.5-2 gal. 36' Auxiliary 2 gal. 40' Cruiser 2.5 gal. 45' Sailboat 3-3.5 gal 50' Sportfisher 4+ gal. Another way to determine bottom paint quantity is to estimate the approximate surface area of the hull below the waterline, using the following formula: Length x Beam x .75 = Approximate underwater surface area in square feet. Each paint has a "theoretical coverage" area, but most paints require at least two coats, so you can expect actual coverage to be no greater than half of the theoretical value. More information For available colors and detailed application instructions, see the Micron CSC Data Sheet. NOTE: Manufacturer data sheets are subject to revision. Linked data sheets are believed to be accurate at the time of publication.
Buying Options
✕Microsoft may receive compensation for clicks on these products, but such compensation has no effect on the ranking or relevance of results
Specifications
Drying Time | Solvent Release |
VOC Content | 370 Grams Per Liter |
Type | Copolymer |
Compatibility | No |
Purpose | Thinner 216/thinner 433 |
Components | 1 |
Active Ingredients | Cuprous Oxide (37.2%) |
Coverage | 440 Sq. Feet Per Gallon |
Biocide | Yes |
Unit Weight | 0.00 Lb |
Number Of Recommended Coats | 2 |
Mfg Part No. | 94-5580g |
Application Temperature | 50.00 °F |
Copper Free | No |
Brand | Interlux |
Dry Film Thickness | 2.00 Mm |
Finish | Matte |